You can usually get a dent out of a table tennis ball by warming it in hot water for a few seconds. The heat makes the air inside the ball expand, and the extra pressure pushes the dent back out. This only works if the ball isn’t cracked. A cracked ball can’t hold the pressure.
Why the Hot Water Trick Works
A table tennis ball is a thin, hollow shell with air sealed inside. For the physics behind it, see why a ping pong ball bounces. When you squash it, the shell bends inwards but the air is still trapped.
Heating the ball does two things:
- The air inside expands, pushing outwards on the dented area.
- The shell softens slightly, making it easier for the dent to flex back into shape.
When the ball cools, the shell firms up again in its rounder shape.
Step-by-Step: The Hot Water Method
You’ll need a heat-safe bowl or mug, hot water and a spoon.
- Heat the water. Water from a kettle that has just boiled works well. For a small dent, very hot tap water is sometimes enough.
- Pour the water into a heat-safe bowl or mug. Use enough to cover the ball.
- Add the ball. It will float, so use the spoon to hold it under, with the dented side down in the water.
- Wait and watch. Small dents often pop out within a few seconds. Turn the ball gently if needed. Don’t leave it in for a long time, as too much heat can warp the shell.
- Lift the ball out with the spoon and put it on a towel.
- Let it cool completely before you touch or play with it.
Be careful with boiling water. Keep children at a safe distance, and don’t hold the ball with your fingers.
Alternative: Using a Hair Dryer
If you don’t want to use hot water, a hair dryer can work:
- Hold the ball with tongs or rest it in a small cup or holder that won’t melt.
- Set the hair dryer to a warm or hot setting and point it at the dent from several inches away.
- Keep the air moving and turn the ball, so one spot doesn’t overheat.
- Stop as soon as the dent pops out, and let the ball cool.
This is usually slower and less even than hot water.
Why We Don’t Recommend Flames
Some guides suggest holding a dented ball over a lighter or candle. We advise against it:
- Celluloid balls are highly flammable. Older balls and some cheap balls are still made of celluloid, and they can catch fire suddenly and burn fast.
- Plastic balls can scorch, melt or warp if they get too hot in one spot.
- It’s hard to tell what a ball is made of just by looking at it.
Hot water does the same job with far less risk.
If the Dent Won’t Come Out
- Try again, briefly. Give the ball another short dip in hot water. Several short dips are better than one long one.
- Check for a crack. Squeeze gently and listen, or look closely along the dent and the seam. If the ball is cracked, it won’t hold pressure, and the dent won’t come out.
- Accept sharp creases. A deep, sharp crease may come out only partly, leaving a ridge or flat spot.
- Hotter isn’t always better. Very long exposure to heat can soften and distort the shell, especially with plastic balls.
Is a Fixed Ball Still Good to Play With?
For casual play, usually yes. For serious practice or matches, probably not. The shell can stretch or thin at the dent, so even a ball that looks round may:
- Bounce slightly lower or less evenly.
- Wobble or move unpredictably in the air.
- Crack more easily later.
A quick test is to drop the repaired ball and a good ball from the same height onto the table and compare the bounce. You can also spin it on the table to see if it wobbles. If it behaves differently, keep it for casual games or throw it away.
Balls are cheap, so for match play it’s best to use undamaged, good-quality balls. Our guide to ITTF-approved table tennis balls explains what to look for when buying.
Preventing Dents
- Pick balls up quickly during practice. Stray balls on the floor are the most common cause of dents.
- Use a ball collector or net for drills.
- Store balls in their box or a holder, away from heat.
- Don’t keep balls in pockets or bags where they can be squashed.
For a broader look at caring for your gear, see our guide to table tennis equipment and gear.